v6 HotEnd Full Kit - 1.75mm Universal (Direct)

63,49 € *
Inhalt: 1 Stück

inkl. MwSt.

Versandkostenfreie Lieferung innerhalb Deutschlands!

Lieferzeit ca. 1-7 Werktage

  • e3d-v6-175mm-direct
E3D-v6: Smaller - Easier - Higher Performance. The E3D-v6 has been redesigned from the... mehr
Produktinformationen "v6 HotEnd Full Kit - 1.75mm Universal (Direct)"

E3D-v6: Smaller - Easier - Higher Performance.

The E3D-v6 has been redesigned from the ground up. We have invested a lot of time and used all of our experience to design E3D's latest and greatest HotEnd. If you would like to know more about the design process, check out this blog post


Print the Widest Range of Materials Possible.

Building on our signature high temperature performance that allows you to print high temperature materials we've now focussed on adding increased functionality with soft and flexible filaments. By providing a PTFE liner tube through the hotend that you can extend into your extruder this gives the ability to add the confinement and constraint needed to make excellent quality prints with flexible filaments like NinjaFlex, FlexPLA and FlexPolyester. This opens up a huge range of new opportunities for your printer.

(PTFE Liner only present in 1.75mm version - 3mm Bowden has partial lining - 3mm Direct has no lining)

This above cutaways show the internals of all three HotEnds. Left to Right: 1.75mm Universal, 3mm Direct, 3mm Bowden. 

 


High Temperature Peformance.

With no PEEK or PTFE in hot regions of our HotEnd we can reach 300C with the supplied thermistor. By swapping a thermistor for a thermocouple (may require additional electronics) you can reach over 400C. 

This not only allows you to print extremely high temperature materials like Polycarbonate and Nylons but also eliminates HotEnd meltdown failures associated with PEEK/PTFE designs. Although our latest v6 hotend has a PTFE liner inside the hotend this liner is never subjected to high temperatures so there is no risk of damaging the liner through overheating.

Our new HeaterBlock gives the fastest heat up times and the most responsive temperature control by clamping around the cartridge for maximum thermal contact. The new thermistor placement means you get the most accurate temperature readings with the fastest response. What this means for you the user is that you can go from 20C to 200C in just 65 seconds, temperature control is responsive enough that you can keep the hotend within 0.5C of your set temperature or less with ease.

 


Reduced Bulk and Z-Height.

We've focussed on cutting as much bulk from the E3Dv6 as possible. This means an overall length of just 62mm and significant reductions in bulk in the X/Y dimensions by using our new injection moulded fan duct.

 


Easy No-Solder, No-Tape, No-Adhesive assembly and maintenance.

We've eliminated Kapton tape or any other adhesives from the assembly process of v6. The new thermistor simply clamps into place with a small screw, high temperature glass sleeving is used to insulate the thermistor legs. This makes installing or removing the thermistor a quick and clean process compared to previous methods involving fiddly kapton taping. No soldering is needed as we supply supply solder free ferrules for making heat-resistant, quick and easy electrical connections to the thermistor legs. Most parts of the hotend simply screw together, the new fan duct simply clips into place and can be oriented in many different directions to suit your particular setup.


High Quality Printing.

We've kept our sharp thermal transition that gives the high quality printing performance users have come to expect from E3D hotends. A sharp thermal break gives better control over filament output so you get more immediate start and stops when extruding as well as retracts that are more effective in combatting ooze. For the user this means sharper more accurate prints that have less stringing, oozing or blobs on the prints.

 


Adaptable To Suit Your Needs.

Our range of nozzle sizes gives you more oppurtunity to choose how you want to print. While our default 0.4mm nozzle gives great prints with a good balance of speed, ease and resolution we are offering a range of nozzles that have special geometries that are tailored to the specific needs of how you want to print. The shape of the tip of the nozzle is key to how the hotend extrudes and flattens a track of plastic. By matching the size of the tip of our nozzles to the width of track of plastic we are able to print with increased resolution in smaller nozzle sizes and with our larger nozzles we've customised the geometry so that you can easily lay down large layers for fast strong prints. Nozzles are easily and quickly changed out because of their hexagonal shape.

 


Easy Mounting and Community Support.

We've kept our same 16mm Groovemount dimensions from v5 to ensure that as much compatibility is maintained as possible with our extensive range of community designed mounts. See here for examples:  Thingiverse

We have an active user base on many printer forums, including RepRap Forums, Google+, SeeMeCNC, Solidoodle, Ultimaker and many others. We also maintain our own E3D Forum where many people share and collaborate on clever solutions for mounting on various printers. We value the community that use our product and look to support development wherever possible.

We're always there to support you in using your HotEnd - whether that means giving advice on public forums, or private email support by our contact system. We stand behind our product and want make sure every customer gets the support they need.

(Note that 3mm Bowden deviates from previous groovemount dimensions slightly - please see drawings for clarification)

 


Great Appearance.

With our CNC machined parts, our injection moulded translucent blue fan duct, neat thermistor mounting with matching blue sleeving we have what we think is a really great looking product. Looks matter, and not only will your prints be the envy of your maker friends, your printer will look great while printing too!

 


Overhauled for Reliability.

We've taken and good hard look at how failures happen and worked with our community to identify and rectify problems. We've developed a new manufacturing process for our heatbreaks that gives a fantastic surface finish which reduces the force needed to restart extrusion which helps reduce forces during frequent and long retractions such as those in bowden systems. We've redesigned the internal shape of our nozzles to reduce pressure needed to extrude which results in increased reliability and better print quality.

​​

 


What's in the box

Metal Parts

  • 1 x Aluminium Heatsink (Contains embedded fitting for tubing in 1.75mm Universal and 3mm Bowden versions)
  • 1 x Stainless Steel Heatbreak
  • 1 x Brass Nozzle (0.4mm)
  • 1 x Aluminium Heater Block

Electronics:

  • 1 x 100K Semitec NTC thermistor
  • 12v 30W Heater Cartridge
  • 1 x 12v 30x30x10mm fan
  • 1 x High Temperature Fiberglass Wire - for Thermistor (150mm) 
  • 2 x 0.75mm Ferrules - for Solder-Free Wire Joins

Fixings:

  • 4 x Plastfast30 3.0 x 16 screws to attach the fan to the fan duct
  • 1 x M3x3 socket dome screw and M3 washer to clamp thermistor
  • 1 x M3x10 socket dome screw to clamp the heater block around the heater cartridge
  • 1 x Fan Duct (Injection Moulded PC)

Bowden Versions also Include:

  • 800mm of appropriately sized PTFE tubing.
  • 1 x Screw in Coupler for extruder end of tubing.

​​


Weiterführende Links zu "v6 HotEnd Full Kit - 1.75mm Universal (Direct)"
Bewertungen lesen, schreiben und diskutieren... mehr
Kundenbewertungen für "v6 HotEnd Full Kit - 1.75mm Universal (Direct)"
15.03.2017

Super HotEnd

Macht einfach Spaß die Drucke gelingen einfach ohne Schwierigkeiten

06.12.2016

Schnelle Lieferung. Hotend funktioniert problemlos. Danke

Schnelle Lieferung. Hotend funktioniert problemlos. Danke

18.11.2016

Rock solid full metal jacket!

Die Montage an einem k8200 ist zwar etwas fummelig, doch ist man vom Velleman nichts anderes gewohnt.

15.04.2016

Top HotEnd. Macht seinem Namen alle Ehre.

War sein Geld wert.

25.02.2016

Gutes Hotend mit genug Leistung

Schnelles Aufheizen und etwas weniger Stringing als mein altes. Nur der Thermistor ist zu fragil, deswegen ein Stern Abzug.

27.01.2016

Top Hotend !

Mit diesem Hotend macht es richtig Spaß zu drucken.
Quallität und Verarbeitung *****

26.11.2015

Super Abwicklung, Artikel naja

Der Artikel kam ausreichend schnell nach Hause.

Was mir allerdings gar nicht zusagt ist das kit an sich. Der Thermistor ist okay was für das Geld aber nicht reicht hier sollte ein schraub Thermistor verwendet werden oder zumindest ein Axial verdrahteter Thermistor genutzt werden der in eine Durchgangsbohrung mit verjüngung gezogen wird. Diese quetschung mit der schraube ist der größte misst . Ich hab sie direkt weggelassen und einen 1% thermistor mit Auspuff Dichtpaste versiegelt.
Einmal 5 min. Auf 230 Grad erwärmen und das Ding ist fest und misst dazu noch genauer. Einen Kurzschluss kann es so auch nicht durch wuetschung geben.

19.08.2015

Tolles Hotend aber kleines Minus

Also das Hotend an und für sich ist klasse, allerdings gibt´s von mir eine kleines Minus. Bei einem "Hotend Full Kit" erwarte ich eigentlich das alle zum Aufbau und Betrieb erfordelichen Teile im Set enthalten sind. Leide fehlt aber bei der "Direct" Version der PTFE-liner (ca 3cm PTFE-Schlauch) um das Hotend wirklich in Betrieb nehmen zu können. (Taucht auch nicht in der Teileliste auf) Ich habe mir mit einem Stück PTFE-Schlauch aus meinem Fundus beholfen, das aber leider nicht 100%ig passt. Über kurz oder lang werde ich mir also den im Shop angebotetnen Bowdenschlauch kaufen (100cm kaufen, von denen ich 3cm benötige). Das finde ich bei einem Hotend dieser Preisklasse schon etwas ärgerlich.

Admin 21.08.2015

Hallo,

das war ein Fehler, es ist normalerweise dabei.
Kommt nach :)

lg
Axel Burger

13.05.2015

Top Ware

Schnelle Lieferung, super Ware

Bewertung schreiben
Bewertungen werden nach Überprüfung freigeschaltet.
Wenn Sie sich Anmelden könnten Sie einen Gutschein für ihre Bewertung erhalten

Die mit einem * markierten Felder sind Pflichtfelder.

5 x Stepper-Motor 17HS4417 (1.7A) Nema17 5 x Stepper-Motor 17HS4417 (1.7A) Nema17
Inhalt 5 Stück (13,99 € * / 1 Stück)
69,95 € *
Versandkostenfrei!
RADDS 1.6 Premiumset Display-Due-RADDS-4xRAPS128 Treiber RADDS 1.6 Premiumset...
Inhalt 1 Stück
219,00 € *
Markenlager LMU10 Linearlager 4-reihig Markenlager LMU10 Linearlager 4-reihig
Inhalt 1 Stück
ab 4,39 € *
Titan Extruder Titan Extruder
Inhalt 1 Stück
ab 48,94 € *
30x30x10mm 12v DC Fan 30x30x10mm 12v DC Fan
Inhalt 1 Stück
7,46 € *
Silicone Socks for v6 - Pack of 3 - Pro Socks Silicone Socks for v6 - Pack of 3 - Pro Socks
Inhalt 3 Stück (1,72 € * / 1 Stück)
5,15 € *
v6 Extra Nozzle - 1.75mm x 0.40mm v6 Extra Nozzle - 1.75mm x 0.40mm
Inhalt 1 Stück
6,52 € *
Kugellager 626zz Kugellager 626zz
Inhalt 1 Stück
0,89 € *
E3D 7mm Nozzle Spanner E3D 7mm Nozzle Spanner
Inhalt 1 Stück
2,00 € *
V6 Silicone Socks (Pack of 3) V6 Silicone Socks (Pack of 3)
Inhalt 1 Stück
5,15 € *
v6 Extra Nozzle - Hardened Steel - für Carbonfilament v6 Extra Nozzle - Hardened Steel - für...
Inhalt 1 Stück
ab 21,00 € *
Stepper-Motor 17HS4417 (1.7A) Nema17 Stepper-Motor 17HS4417 (1.7A) Nema17
Inhalt 1 Stück
14,95 € *
v6 Extra Nozzle - 1.75mm x 0.60mm v6 Extra Nozzle - 1.75mm x 0.60mm
Inhalt 1 Stück
6,52 € *
v6 Extra Nozzle - 1.75mm x 0.80mm v6 Extra Nozzle - 1.75mm x 0.80mm
Inhalt 1 Stück
6,52 € *
v6 Extra Nozzle - 1.75mm x 0.35mm v6 Extra Nozzle - 1.75mm x 0.35mm
Inhalt 1 Stück
6,52 € *
v6 Extra Nozzle - 1.75mm x 0.25mm v6 Extra Nozzle - 1.75mm x 0.25mm
Inhalt 1 Stück
11,57 € *
Versandkostenfrei!
Nozzle X - V6 1.75mm / 3mm Nozzle X - V6 1.75mm / 3mm
Inhalt 1 Stück
ab 32,00 € *
Thermistor Cartridge Thermistor Cartridge
Inhalt 1 Stück
9,00 € *
Nozzle Fun Pack! 1,75mm Nozzle Fun Pack! 1,75mm
Inhalt 1 Stück
40,00 € *
1m Bowden (1.75mm Filament) 1m Bowden (1.75mm Filament)
Inhalt 1 Stück
7,18 € *
v6 Heat Break (1.75mm) v6 Heat Break (1.75mm)
Inhalt 1 Stück
10,03 € *
Versandkostenfrei!
RADDS 1.6 Premiumset Display-Due-RADDS-4xRAPS128 Treiber RADDS 1.6 Premiumset...
Inhalt 1 Stück
219,00 € *
Plated Copper-Alloy Nozzle Plated Copper-Alloy Nozzle
Inhalt 1 Stück
ab 14,06 € *
Lüfter 30x10 12VDC 0,58W 9,34m3/h VAPO Lüfter 30x10 12VDC 0,58W 9,34m3/h VAPO
Inhalt 1 Stück
10,00 € *
Markenlager LMU10 Linearlager 4-reihig Consumerreihe Markenlager LMU10 Linearlager 4-reihig...
Inhalt 1 Stück
ab 2,39 € *
Heater Cartridge - 12v - 40w Heater Cartridge - 12v - 40w
Inhalt 1 Stück
11,07 € *
Wellenkupplung flexibel 5x6 mm Wellenkupplung flexibel 5x6 mm
Inhalt 1 Stück
5,95 € *
RAPS128 Schrittmotortreiber NG RAPS128 Schrittmotortreiber NG
Inhalt 1 Stück
19,50 € *
Markenlager LMU10 Linearlager 4-reihig Markenlager LMU10 Linearlager 4-reihig
Inhalt 1 Stück
ab 4,39 € *
v6 Extra Nozzle - 1.75mm x 0.3mm v6 Extra Nozzle - 1.75mm x 0.3mm
Inhalt 1 Stück
6,52 € *
RADDS Hall-E Endstop (3,3-5Volt) RADDS Hall-E Endstop (3,3-5Volt)
Inhalt 1 Stück
12,00 € *
RADDS Board V1.6 12V/24V RADDS Board V1.6 12V/24V
Inhalt 1 Stück
69,00 € *
Stepper-Motor 42BYGHW811 (2.5A) Nema17 Stepper-Motor 42BYGHW811 (2.5A) Nema17
Inhalt 1 Stück
17,95 € *
SSR Relais DC-DC 40A mit Kühlkörper SSR Relais DC-DC 40A mit Kühlkörper
Inhalt 1 Stück
28,00 € *
Capricorn Bowden Tubing (10cm) Capricorn Bowden Tubing (10cm)
Inhalt 0.1 Laufende(r) Meter (18,50 € * / 1 Laufende(r) Meter)
1,85 € *
Creality K1 Max zur Miete Creality K1 Max zur Miete
Inhalt 1 Stück
ab 89,00 € *
Versandkostenfrei!
V6 All-Metal HotEnd V6 All-Metal HotEnd
Inhalt 1 Stück
ab 50,00 € *
Versandkostenfrei!
Voron2 V2.4 R2 Kit - 250 x 250 x 250mm Voron2 V2.4 R2 Kit - 250 x 250 x 250mm
Inhalt 1 Stück
ab 950,00 € *
Versandkostenfrei!
Voron2 V2.4 R2 Kit - 300 x 300 x 300mm Voron2 V2.4 R2 Kit - 300 x 300 x 300mm
Inhalt 1 Stück
ab 1.052,00 € *
Versandkostenfrei!
TEVO Tornado Upgrade Kit TEVO Tornado Upgrade Kit
Inhalt 1 Stück
92,00 € *
Versandkostenfrei!
Versandkostenfrei!
v6 HotEnd Full Kit - Assembled v6 HotEnd Full Kit - Assembled
Inhalt 1 Stück
ab 73,00 € *
Kraken Kraken
Inhalt 1 Stück
225,13 € *
Versandkostenfrei!
Simplify 3D V5.0 Software Simplify 3D V5.0 Software
Inhalt 1 Stück
199,00 € *
Silikon-Heizmatte 24V Silikon-Heizmatte 24V
Inhalt 1 Stück
26,99 € *
Zuletzt angesehen