v6 HotEnd Full Kit - 1.75mm Universal (with Bowden add-on)

76,00 € *
Inhalt: 1 Stück

inkl. MwSt.

Versandkostenfreie Lieferung innerhalb Deutschlands!

Lieferzeit ca. 1-7 Werktage

  • SW10204
Doku: https://e3d-online.dozuki.com/ E3D-v6: Smaller - Easier - Higher... mehr
Produktinformationen "v6 HotEnd Full Kit - 1.75mm Universal (with Bowden add-on)"
Doku: https://e3d-online.dozuki.com/

E3D-v6: Smaller - Easier - Higher Performance.

The E3D-v6 has been redesigned from the ground up. We have invested a lot of time and used all of our experience to design E3D's latest and greatest HotEnd. If you would like to know more about the design process, check out this blog post


Print the Widest Range of Materials Possible.

Building on our signature high temperature performance that allows you to print high temperature materials we've now focussed on adding increased functionality with soft and flexible filaments. By providing a PTFE liner tube through the hotend that you can extend into your extruder this gives the ability to add the confinement and constraint needed to make excellent quality prints with flexible filaments like NinjaFlex, FlexPLA and FlexPolyester. This opens up a huge range of new opportunities for your printer.

(PTFE Liner only present in 1.75mm version - 3mm Bowden has partial lining - 3mm Direct has no lining)

This above cutaways show the internals of all three HotEnds. Left to Right: 1.75mm Universal, 3mm Direct, 3mm Bowden. 

 


High Temperature Peformance.

With no PEEK or PTFE in hot regions of our HotEnd we can reach 300C with the supplied thermistor. By swapping a thermistor for a thermocouple (may require additional electronics) you can reach over 400C. 

This not only allows you to print extremely high temperature materials like Polycarbonate and Nylons but also eliminates HotEnd meltdown failures associated with PEEK/PTFE designs. Although our latest v6 hotend has a PTFE liner inside the hotend this liner is never subjected to high temperatures so there is no risk of damaging the liner through overheating.

Our new HeaterBlock gives the fastest heat up times and the most responsive temperature control by clamping around the cartridge for maximum thermal contact. The new thermistor placement means you get the most accurate temperature readings with the fastest response. What this means for you the user is that you can go from 20C to 200C in just 65 seconds, temperature control is responsive enough that you can keep the hotend within 0.5C of your set temperature or less with ease.

 


Reduced Bulk and Z-Height.

We've focussed on cutting as much bulk from the E3Dv6 as possible. This means an overall length of just 62mm and significant reductions in bulk in the X/Y dimensions by using our new injection moulded fan duct.

 


Easy No-Solder, No-Tape, No-Adhesive assembly and maintenance.

We've eliminated Kapton tape or any other adhesives from the assembly process of v6. The new thermistor simply clamps into place with a small screw, high temperature glass sleeving is used to insulate the thermistor legs. This makes installing or removing the thermistor a quick and clean process compared to previous methods involving fiddly kapton taping. No soldering is needed as we supply supply solder free ferrules for making heat-resistant, quick and easy electrical connections to the thermistor legs. Most parts of the hotend simply screw together, the new fan duct simply clips into place and can be oriented in many different directions to suit your particular setup.


High Quality Printing.

We've kept our sharp thermal transition that gives the high quality printing performance users have come to expect from E3D hotends. A sharp thermal break gives better control over filament output so you get more immediate start and stops when extruding as well as retracts that are more effective in combatting ooze. For the user this means sharper more accurate prints that have less stringing, oozing or blobs on the prints.

 


Adaptable To Suit Your Needs.

Our range of nozzle sizes gives you more oppurtunity to choose how you want to print. While our default 0.4mm nozzle gives great prints with a good balance of speed, ease and resolution we are offering a range of nozzles that have special geometries that are tailored to the specific needs of how you want to print. The shape of the tip of the nozzle is key to how the hotend extrudes and flattens a track of plastic. By matching the size of the tip of our nozzles to the width of track of plastic we are able to print with increased resolution in smaller nozzle sizes and with our larger nozzles we've customised the geometry so that you can easily lay down large layers for fast strong prints. Nozzles are easily and quickly changed out because of their hexagonal shape.

 


Easy Mounting and Community Support.

We've kept our same 16mm Groovemount dimensions from v5 to ensure that as much compatibility is maintained as possible with our extensive range of community designed mounts. See here for examples:  Thingiverse

We have an active user base on many printer forums, including RepRap Forums, Google+, SeeMeCNC, Solidoodle, Ultimaker and many others. We also maintain our own E3D Forum where many people share and collaborate on clever solutions for mounting on various printers. We value the community that use our product and look to support development wherever possible.

We're always there to support you in using your HotEnd - whether that means giving advice on public forums, or private email support by our contact system. We stand behind our product and want make sure every customer gets the support they need.

(Note that 3mm Bowden deviates from previous groovemount dimensions slightly - please see drawings for clarification)

 


Great Appearance.

With our CNC machined parts, our injection moulded translucent blue fan duct, neat thermistor mounting with matching blue sleeving we have what we think is a really great looking product. Looks matter, and not only will your prints be the envy of your maker friends, your printer will look great while printing too!

 


Overhauled for Reliability.

We've taken and good hard look at how failures happen and worked with our community to identify and rectify problems. We've developed a new manufacturing process for our heatbreaks that gives a fantastic surface finish which reduces the force needed to restart extrusion which helps reduce forces during frequent and long retractions such as those in bowden systems. We've redesigned the internal shape of our nozzles to reduce pressure needed to extrude which results in increased reliability and better print quality.

​​

 


What's in the box

Metal Parts

  • 1 x Aluminium Heatsink (Contains embedded fitting for tubing in 1.75mm Universal and 3mm Bowden versions)
  • 1 x Stainless Steel Heatbreak
  • 1 x Brass Nozzle (0.4mm)
  • 1 x Aluminium Heater Block

Electronics:

  • 1 x 100K Semitec NTC thermistor
  • 12v 30W Heater Cartridge
  • 1 x 12v 30x30x10mm fan
  • 1 x High Temperature Fiberglass Wire - for Thermistor (150mm) 
  • 2 x 0.75mm Ferrules - for Solder-Free Wire Joins

Fixings:

  • 4 x Plastfast30 3.0 x 16 screws to attach the fan to the fan duct
  • 1 x M3x3 socket dome screw and M3 washer to clamp thermistor
  • 1 x M3x10 socket dome screw to clamp the heater block around the heater cartridge
  • 1 x Fan Duct (Injection Moulded PC)

Bowden Versions also Include:

  • 800mm of appropriately sized PTFE tubing.
  • 1 x Screw in Coupler for extruder end of tubing.

​​


Weiterführende Links zu "v6 HotEnd Full Kit - 1.75mm Universal (with Bowden add-on)"
Bewertungen lesen, schreiben und diskutieren... mehr
Kundenbewertungen für "v6 HotEnd Full Kit - 1.75mm Universal (with Bowden add-on)"
18.05.2017

Alles Super

Zuverlässige Lieferung. Gute Qualität und guter unkomplizierter Service. Kontaktaufnahme ist ebenfalls einfach.

19.03.2017

Gutes Hotend

Das Hotend macht einen guten Eindruck. Auch ist hier im Gegensatz zu den Chinaclonen der Heatbreaker komplett in Metall ausgeführt. Das Kit hat zwei 0,4mm Düsen dabei. Etwas störend ist, dass der Heatbreaker, wenn man die mitgelieferte Wärmeleitpaste benutzt locker im Kühler sitzt und sich dann leicht drehen lässt.

27.01.2017

Gute Verbesserungen am Druckkopf.

Insgesamt gelungene präzise Verarbeitung. Gute Verbesserung bei
der Wäreisolation.
Würde mir noch eine alternative Lüfterhalterung (für weiteren Druckkopflüfter) wünschen.

29.08.2016

Sehr gute Qualität

habe damit mein altes billiges Hotend aus China, welches nicht zu vergleichen ist, ausgetauscht. Top Qualität, hervorragende Leistung, druck Ergebnisse haben sich deutlich verbessert. Für den Preis bekommt man was man will!

26.02.2016

Top Zustand und schnelle Lieferung

19.02.2016

Danke gerne wieder!

Ein rechtzeitiger Hinweis, das die ware versendet ist,
wäre sehr hilfreich für Alle. Sonst ist alles Gut.

15.02.2016

Extreme Aufwertung meines Druckers

Ich habe dieses Hotend - neben einigen anderen Modifikationen - an meinen Deltaprintr gebaut. Seither sind die Druckleistungen um ein Vielfaches konstanter. Gedruckte Objekte erscheinen makellos, ohne Blobs und andere Verunstaltungen. Der Metallaufbau macht die Kühlung des Hotends mit einem kleinen Lüfter (ich habe statt des mitgelieferten einen 40 mm Sunon verbaut) sehr effektiv. Zudem verträgt das Hotend somit mehrere (De-)Montagen, bspw. zu Reinigungszwecken. Ganz klare Kaufempfehlung!

07.01.2016

Super Teil diese Hotend

Das Hotend ist einfach zu monieren, alles paßt hervorragen. Die Performance ist hervorragend. Sehr kurze Heizzeiten. Klasse Druckergebnisse.

22.10.2015

Gute Verarbeitung und hervorragende Druckergebnisse

Das Hotend ist sehr gut verarbeitet und lässt sich größtenteils einfach zusammenbauen. Ich bin mit den bisherigen Druckergebnissen sehr zufrieden, kein vergleich zu meinem vorherigem billig Hotend.

12.10.2015

Super Qualität, schnelle Lieferung, toll verpackt

Super Qualität, schnelle Lieferung, toll verpackt, jederzeit wieder.....

20.07.2015

Top Qualität, schnelle Lieferung, super Service

Bewertung schreiben
Bewertungen werden nach Überprüfung freigeschaltet.
Wenn Sie sich Anmelden könnten Sie einen Gutschein für ihre Bewertung erhalten
Bitte geben Sie die Zeichenfolge in das nachfolgende Textfeld ein.

Die mit einem * markierten Felder sind Pflichtfelder.

Versandkostenfrei!
v6 HotEnd Full Kit - 3.00mm Bowden v6 HotEnd Full Kit - 3.00mm Bowden v6 HotEnd Full Kit - 3.00mm Bowden
Inhalt 1 Stück
76,00 € *
5 x Stepper-Motor 42BYGHW811 (2.5A) Nema17 5 x Stepper-Motor 42BYGHW811 (2.5A) Nema17
Inhalt 5 Stück (16,59 € * / 1 Stück)
82,95 € *
1m Bowden (3mm Filament) 1m Bowden (3mm Filament)
Inhalt 1 Stück
10,00 € *
MK8 Drive Gear für 1.75mm oder 3mm Filament MK8 Drive Gear für 1.75mm oder 3mm Filament MK8 Drive Gear für 1.75mm oder 3mm Filament
Inhalt 1 Stück
8,00 € *
GT2 Riemen meterweise GT2 Riemen meterweise
Inhalt 1 Laufende(r) Meter
4,99 € *
Titan Extruder Titan Extruder Titan Extruder
Inhalt 1 Stück
ab 66,00 € *
v6 Extra Nozzle - 1.75mm x 0.40mm v6 Extra Nozzle - 1.75mm x 0.40mm v6 Extra Nozzle - 1.75mm x 0.40mm
Inhalt 1 Stück
7,39 € *
v6 Extra Nozzle - 1.75mm x 0.3mm v6 Extra Nozzle - 1.75mm x 0.3mm v6 Extra Nozzle - 1.75mm x 0.3mm
Inhalt 1 Stück
10,79 € *
GT2 Pulley 20Zähne GT2 Pulley 20Zähne
Inhalt 1 Stück
5,29 € *
v6 Extra Nozzle - 1.75mm x 0.25mm v6 Extra Nozzle - 1.75mm x 0.25mm v6 Extra Nozzle - 1.75mm x 0.25mm
Inhalt 1 Stück
12,00 € *
Silicone Socks for v6 - Pack of 3 - Pro Socks Silicone Socks for v6 - Pack of 3 - Pro Socks Silicone Socks for v6 - Pack of 3 - Pro Socks
Inhalt 3 Stück (1,67 € * / 1 Stück)
5,00 € *
Threaded Bowden Coupling (1.75mm Filament) Threaded Bowden Coupling (1.75mm Filament)
Inhalt 1 Stück
2,39 € *
Plated Copper-Alloy Nozzle Plated Copper-Alloy Nozzle Plated Copper-Alloy Nozzle
Inhalt 1 Stück
ab 12,49 € *
PLA 1.75 mm Farbe nach Wahl PLA 1.75 mm Farbe nach Wahl
Inhalt 0.75 Kilogramm (26,67 € * / 1 Kilogramm)
20,00 € *
Nozzle Fun Pack! 1,75mm Nozzle Fun Pack! 1,75mm Nozzle Fun Pack! 1,75mm
Inhalt 1 Stück
39,00 € *
1m Bowden (1.75mm Filament) 1m Bowden (1.75mm Filament)
Inhalt 1 Stück
10,00 € *
V6 Silicone Socks (Pack of 3) V6 Silicone Socks (Pack of 3) V6 Silicone Socks (Pack of 3)
Inhalt 1 Stück
5,00 € *
v6 Extra Nozzle - 1.75mm x 0.60mm v6 Extra Nozzle - 1.75mm x 0.60mm v6 Extra Nozzle - 1.75mm x 0.60mm
Inhalt 1 Stück
7,39 € *
Lüfter 12V 40x40mm Lüfter 12V 40x40mm
5,50 € *
E3D 7mm Nozzle Spanner E3D 7mm Nozzle Spanner E3D 7mm Nozzle Spanner
Inhalt 1 Stück
1,00 € *
RAPS128 Schrittmotortreiber NG RAPS128 Schrittmotortreiber NG RAPS128 Schrittmotortreiber NG
Inhalt 1 Stück
17,49 € *
Fibreglass Sleeving for Insulating Thermistors (100mm) Fibreglass Sleeving for Insulating Thermistors...
Inhalt 1 Stück
0,50 € *
3D Lac – Sprühkleber 3D Lac – Sprühkleber 3D Lac – Sprühkleber
Inhalt 0.4 Liter (21,25 € * / 1 Liter)
8,50 € *
Innensechskantschrauben M3x30 DIN912 Innensechskantschrauben M3x30 DIN912
ab 1,79 € *
Hobb-Goblin - 5mm ID Drive Gear Hobb-Goblin - 5mm ID Drive Gear Hobb-Goblin - 5mm ID Drive Gear
Inhalt 1 Stück
12,00 € *
v6 Extra Nozzle - Hardened Steel - für Carbonfilament v6 Extra Nozzle - Hardened Steel - für Carbonfilament v6 Extra Nozzle - Hardened Steel - für...
Inhalt 1 Stück
ab 24,00 € *
Endstop Microswitches - Omron D2F-01FL Endstop Microswitches - Omron D2F-01FL Endstop Microswitches - Omron D2F-01FL
Inhalt 1 Stück
2,49 € *
RADDS Board V1.6 12V/24V RADDS Board V1.6 12V/24V
Inhalt 1 Stück
57,90 € *
Markenlager LMU8 Linearlager 4-reihig Markenlager LMU8 Linearlager 4-reihig
Inhalt 1 Stück
ab 4,10 € *
Markenkugellager 608zz Markenkugellager 608zz
Inhalt 1 Stück
ab 2,59 € *
Sechskantmuttern DIN 934 V2A M3 Sechskantmuttern DIN 934 V2A M3
ab 0,59 € *
Filament 1.75mm ABS Farbe nach Wahl Filament 1.75mm ABS Farbe nach Wahl
Inhalt 0.75 Kilogramm (26,60 € * / 1 Kilogramm)
ab 19,95 € *
v6 Extra Nozzle - Stainless Steel - 1.75mm x 0.4mm v6 Extra Nozzle - Stainless Steel - 1.75mm x 0.4mm
Inhalt 1 Stück
24,00 € *
Threaded Bowden Coupling + 1m Bowden (1.75mm Filament) Threaded Bowden Coupling + 1m Bowden (1.75mm Filament) Threaded Bowden Coupling + 1m Bowden (1.75mm...
Inhalt 1 Stück
10,00 € *
v6 Heat Break (1.75mm) v6 Heat Break (1.75mm)
Inhalt 1 Stück
12,00 € *
v6 Extra Nozzle - 1.75mm x 0.35mm v6 Extra Nozzle - 1.75mm x 0.35mm v6 Extra Nozzle - 1.75mm x 0.35mm
Inhalt 1 Stück
9,00 € *
Stepper-Motor 17HS4417 (1.7A) Nema17 Stepper-Motor 17HS4417 (1.7A) Nema17
Inhalt 1 Stück
14,95 € *
Innensechskantschrauben M3x10 DIN912 Innensechskantschrauben M3x10 DIN912
ab 1,59 € *
Nozzle Plated Wear Resistant RepRap - M6 Thread 1.75mm Filament (E3D V5-V6, Prusa i3 MK2) Nozzle Plated Wear Resistant RepRap - M6 Thread 1.75mm Filament (E3D V5-V6, Prusa i3 MK2) Nozzle Plated Wear Resistant RepRap - M6 Thread...
Inhalt 1 Stück
19,00 € *
Radiallüfter 40x40x20 Radiallüfter 40x40x20 Radiallüfter 40x40x20
Inhalt 1 Stück
3,99 € *
Wellenkupplung flexibel 5x6 mm Wellenkupplung flexibel 5x6 mm
Inhalt 1 Stück
5,95 € *
DryLin® sphärische Gewindemutter mit Stehlagergehäuse 10x2 DryLin® sphärische Gewindemutter mit...
Inhalt 1 Stück
22,65 € *
Wellenkupplung flexibel 5x5 mm Wellenkupplung flexibel 5x5 mm
Inhalt 1 Stück
5,95 € *
v6 HotEnd Full Kit - Assembled v6 HotEnd Full Kit - Assembled v6 HotEnd Full Kit - Assembled
Inhalt 1 Stück
ab 84,99 € *
endmontiertes v6 HotEnd Full Kit - 1.75mm Universal (Direct) endmontiertes v6 HotEnd Full Kit - 1.75mm Universal (Direct) endmontiertes v6 HotEnd Full Kit - 1.75mm...
Inhalt 1 Stück
85,00 € *
Versandkostenfrei!
v6 HotEnd Full Kit - 1.75mm Universal (Direct) v6 HotEnd Full Kit - 1.75mm Universal (Direct) v6 HotEnd Full Kit - 1.75mm Universal (Direct)
Inhalt 1 Stück
67,00 € *
Versandkostenfrei!
E3D Hemera Bowden Kit E3D Hemera Bowden Kit E3D Hemera Bowden Kit
Inhalt 1 Stück
98,00 € *
Versandkostenfrei!
E3D Hemera Direct Kit E3D Hemera Direct Kit E3D Hemera Direct Kit
Inhalt 1 Stück
127,00 € *
Versandkostenfrei!
Prusa V6 HotEnd Prusa V6 HotEnd Prusa V6 HotEnd
Inhalt 1 Stück
ab 63,00 € *
Versandkostenfrei!
Volcano HotEnd Volcano HotEnd Volcano HotEnd
Inhalt 1 Stück
ab 67,00 € *
Nylon CF15 Carbon Nylon CF15 Carbon Nylon CF15 Carbon
Inhalt 0.6 Kilogramm (86,67 € * / 1 Kilogramm)
52,00 € *
Silikonheizmatte 24V 400W mit 3M Klebefolie und Thermistor Silikonheizmatte 24V 400W mit 3M Klebefolie und...
Inhalt 1 Stück
40,00 € *
EZ-Stik Cold 3D Printer Build Surface EZ-Stik Cold 3D Printer Build Surface
Inhalt 1 Stück
ab 16,00 € *
High Precision Heater Cartridge 12V/24V High Precision Heater Cartridge 12V/24V High Precision Heater Cartridge 12V/24V
Inhalt 1 Stück
18,30 € *
Upgradekit e3d Hotends HeatBreak+Düse Upgradekit e3d Hotends HeatBreak+Düse Upgradekit e3d Hotends HeatBreak+Düse
Inhalt 1 Stück
35,00 € *
The V6 GOLD Edition HotEnd 12V/24V The V6 GOLD Edition HotEnd 12V/24V The V6 GOLD Edition HotEnd 12V/24V
Inhalt 1 Stück
97,00 € *
Chimera Chimera Chimera
Inhalt 1 Stück
114,00 € *
Plated Copper-Alloy Heater Block 500° Heizkopf Plated Copper-Alloy Heater Block 500° Heizkopf Plated Copper-Alloy Heater Block 500° Heizkopf
Inhalt 1 Stück
28,00 € *
Block & Sock - V6 Upgrade kit Block & Sock - V6 Upgrade kit Block & Sock - V6 Upgrade kit
Inhalt 1 Stück
21,00 € *
Titan Extruder Titan Extruder Titan Extruder
Inhalt 1 Stück
ab 66,00 € *
e3d lite Bowden 12V e3d lite Bowden 12V
Inhalt 1 Stück
40,00 € *
e3d lite 24V e3d lite 24V
Inhalt 1 Stück
35,00 € *
24V Extruder + v6 HotEnd Full Kit - 1.75mm Universal (with Bowden add-on) 24V Extruder + v6 HotEnd Full Kit - 1.75mm Universal (with Bowden add-on) 24V Extruder + v6 HotEnd Full Kit - 1.75mm...
Inhalt 1 Stück
ab 114,95 € *
1m Bowden (3mm Filament) 1m Bowden (3mm Filament)
Inhalt 1 Stück
10,00 € *
RADDS Board V1.6 12V/24V RADDS Board V1.6 12V/24V
Inhalt 1 Stück
57,90 € *
RAPS128 Schrittmotortreiber NG RAPS128 Schrittmotortreiber NG RAPS128 Schrittmotortreiber NG
Inhalt 1 Stück
17,49 € *
Versandkostenfrei!
v6 HotEnd Full Kit 24v - 1.75mm Universal (Direct) v6 HotEnd Full Kit 24v - 1.75mm Universal (Direct) v6 HotEnd Full Kit 24v - 1.75mm Universal (Direct)
Inhalt 1 Stück
67,00 € *
Versandkostenfrei!
v6 HotEnd Full Kit 24v - 1.75mm Universal (with Bowden add-on) v6 HotEnd Full Kit 24v - 1.75mm Universal (with Bowden add-on) v6 HotEnd Full Kit 24v - 1.75mm Universal (with...
Inhalt 1 Stück
76,00 € *
v6 HeatSink - 1.75mm Universal (With Bowden Fitting) v6 HeatSink - 1.75mm Universal (With Bowden Fitting) v6 HeatSink - 1.75mm Universal (With Bowden...
Inhalt 1 Stück
17,00 € *
v6 Heat Break (1.75mm) v6 Heat Break (1.75mm)
Inhalt 1 Stück
12,00 € *
v6 HotEnd Metal Parts Only - 1.75mm Universal v6 HotEnd Metal Parts Only - 1.75mm Universal v6 HotEnd Metal Parts Only - 1.75mm Universal
Inhalt 1 Stück
51,00 € *
Markenlager LMU10 Linearlager 4-reihig Markenlager LMU10 Linearlager 4-reihig
Inhalt 1 Stück
ab 4,39 € *
Versandkostenfrei!
RADDS 1.6 Premiumset Display-Due-RADDS-4xRAPS128 Treiber RADDS 1.6 Premiumset...
Inhalt 1 Stück
199,00 € *
RADDS Display 20x4 RADDS Display 20x4
Inhalt 1 Stück
ab 40,00 € *
Arduino Due Arduino Due Arduino Due
Inhalt 1 Stück
39,00 € *
Kapton-Heizmatte 12V mit SSR Relais und Kühler Kapton-Heizmatte 12V mit SSR Relais und Kühler Kapton-Heizmatte 12V mit SSR Relais und Kühler
Inhalt 1 Stück
56,00 € *
Kapton-Heizmatte 24V Kapton-Heizmatte 24V
Inhalt 1 Stück
26,99 € *
Zuletzt angesehen